FPGA DEVICES · ENGINEERING · SOURCING Source-linked information. Clear project requirements.

Hard-to-find

72V215L10TFG: preserve the 512 × 18 FIFO timing and stop margin

Published · Updated

72V215L10TFG is a 3.3 V,512 ×18 synchronous FIFO for an ordered parallel data stream. This dossier helps a legacy-board buyer preserve the exact identity and helps an engineer review the existing buffering contract. Original LTB and LTS dates have passed; current stock, price, lead time and lot condition require a specific offer.

View the manufacturer part record · Read the official electrical datasheet · Get Price & Lead Time — 72V215L10TFG,25 pieces

Match the complete order code to the affected row

The exact order code and its withdrawal timeline72V215L10TFG connects to the exact row in PLC250016. Issue May30 2025, final LTB November30 2025, last shipment May30 2026. Documentary concept, not availability.ONE CODE · ONE AFFECTED ROW72V215L10TFG2025-05-30Notice issued2025-11-30Final last-time buy2026-05-30Last shipmentHistorical events ≠ current stock
Original documentary timeline for this exact affected code. Historical events do not establish present supply.
Show shared complete-order-code concept walkthrough (GIF)
Shared original order-code transcription concept using other example parts, not this FIFO's specifications
Shared original complete-order-code concept animation. Open this disclosure to view it; leave it closed to use the static transcript below. Its other example codes do not specify or test 72V215L10TFG.

Static transcript for this FIFO

  1. Copy 72V215L10TFG exactly from the released BOM. Compare the quotation and container label as separate records; preserve the spelling rather than normalizing it.
  2. For this FIFO only, the cited ordering table identifies L as low power, 10 as the commercial 10 ns cycle grade, TF as the slim thin plastic quad flatpack family, and G as green. The absent I denotes the commercial temperature grade.
  3. This exact code has no final 8 and its exact-part page lists tray carrier. The ordering scheme uses a final 8 for tape and reel. Record a proposed carrier-code change separately rather than silently changing the requested MPN.
  4. The shared animation uses other example order codes. Their suffix meanings, packages, electrical limits and timing are not 72V215L10TFG specifications. Neither the animation nor this transcript is a hardware test, simulation result, lot-authentication result or compatibility approval.

FIFO-specific source: DSC-4294/8, p. 25, ordering information; Renesas exact-part carrier and grade record.

72V215L10TFG is a Renesas / IDT synchronous FIFO organized as 512 words of 18 bits. It serves an ordered stream through separate input and output ports. This is useful when a legacy board must preserve a producer-to-consumer buffering contract: the board expects both the stored word sequence and particular ready, empty, and full behavior. A maintenance purchase therefore needs more than the same nominal memory capacity. The timing mode, clock arrangement, voltage, package, and commercial temperature range belong in the identification record. Source: exact-part Product Attributes, fetched November 10, 2026.

The original PLC250016 notice is dated May 30, 2025 (2025-05-30). Its exact affected-parts table on PDF page 3 names 72V215L10TFG, records November 30, 2025 (2025-11-30) as the final last-time-buy date, and May 30, 2026 (2026-05-30) as the last-shipment date. The replacement column says None. Both milestones are historical by this dossier's November 10, 2026 review date. These dates explain the original manufacturer's withdrawal process; they do not establish that an independent supplier has stock, that a quoted lot is authentic, or that an order can still be placed with the manufacturer. Source: PLC250016, issue May 30, 2025, pp. 1 and 3, exact affected row.

Preserve the literal order code on the released BOM, supplier quotation, outer-container label, and receiving record. The datasheet ordering information identifies L as low power, 10 as the 10 ns clock-cycle grade, TF as the slim thin plastic quad flatpack family, and G as green. The absence of I denotes the commercial range. A final 8 denotes tape and reel in the ordering scheme; this exact code has no final 8 and its current exact-part page lists tray carrier. Do not silently add that carrier suffix to a purchase request or merge the two identities. Source: DSC-4294/8, March 2018, p. 25, ordering information. Source: exact-part page, carrier and temperature.

There are two lifecycle contexts in the source set. The March 2018 datasheet banner describes an earlier SnPb lead-finish discontinuance with a June 2018 last-time-buy date. That banner is not the lifecycle date for this G order code. Use the exact affected row in PLC250016 and retain the datasheet for electrical and functional evidence. The notice's original LTB process had non-cancellable/non-returnable shipment terms and manufacturer acceptance conditions. An independent supplier's present terms require a separate quotation. Start from the hard-to-find sourcing workflow to organize that evidence. Source: DSC-4294/8, pp. 1 and 25, SnPb banner. Source: PLC250016, p. 1, original response conditions.

A 512 by 18 buffer is a time budget

320 words of usable headroom in the worked caseA512word Standard mode FIFO has128occupied words,320usable words and64reserved words. At assumed25million writes per second, usable headroom is12.8microseconds. Not measured performance.STANDARD MODE · 512 WORDS128 occupied320 usable headroom64 reserved for stop response320 ÷ 25,000,000= 12.8 microseconds
Original occupancy budget. Assumptions: Standard mode;25 million accepted writes/s;128 occupied;64 reserved. Not measured performance.

The array holds 9,216 bits, calculated as 512 × 18. If an application places a 16-bit sample and two status bits in each word, the array stores 512 complete sample records. It does not store 576 such records simply because 9,216 divided by 16 is 576: that division discards the status-bit contract. The record definition should say whether the two extra bits carry parity, tags, packet boundaries, or unused values. Their interpretation comes from the board design, not from the memory's width alone. Source: DSC-4294/8, p. 1, 512 × 18 organization.

Consider an explicitly assumed planning case: writes are accepted at 25 million words per second, the consumer stops completely, and the FIFO starts empty in Standard mode. Ignoring all safety reserve, 512 / 25,000,000 gives 20.48 microseconds until 512 words have arrived. This is an occupancy calculation, not a measured stall tolerance. If 128 words were already queued and 64 locations must remain reserved for stopping the producer, the usable increment becomes 512 − 128 − 64 = 320 words, or 12.8 microseconds. A board that must survive a longer interruption needs a different operating policy or a redesigned buffer.

Reserve space should be derived from the whole stop path. Assume 2 microseconds from a stop request to the producer's final newly issued word. At the assumed write rate that contributes 50 words. Add 10 already committed pipeline words and a separate, explicitly assumed allowance of 4 words for flag visibility and control response: the illustrative reserve is 64 words. None of those latency assumptions is a tested property of this board. Replace them with bounded values for the actual clock domains, selected flag configuration, controller, and upstream interface.

For 72V215 in Standard mode, the datasheet's default full offset is 63 words; its table describes almost-full assertion at 512 − 63 = 449 queued words. The illustrative 64-word reserve instead requires action by an occupancy of 448 words. The difference is one location, but the default is insufficient for these assumptions. Derive and program the offset using the source procedure, then verify assertion timing and all subsequent accepted writes. For continuous unequal rates, compute occupancy growth from accepted writes minus accepted reads. A finite FIFO cannot cure a permanent average-rate deficit. Source: DSC-4294/8, pp. 6–9; p. 7 Table 1 and default-offset notes.

A redesign using embedded memory can begin with the BRAM organization estimate: enter width 18 and depth 512, then supply a legal primitive width, depth, and port arrangement from the actual target FPGA documentation. Its block-count lower bound and unused-capacity output do not implement FIFO flags, reproduce this part's reset behavior, or approve a replacement. Keep this capacity screen separate from the later implementation, constraints, and verification work.

Reset chooses the read contract and flag behavior

Reset selects two different read contractsReset connects to Standard mode, first word requested, or FWFT mode, first word falls through under the documented clock sequence. Flag interpretation follows selection. Conceptual diagram, not a waveform.RESET CONFIGURATIONSTANDARDRequest thefirst wordFWFTFirst wordfalls throughMatch flag polarity and latency
Original reset-mode concept, not a timing waveform. Source Tables 3–5 govern actual configuration.

A FIFO port can look correct on a schematic while its controller uses the wrong first-word convention. This family supports IDT Standard mode and First Word Fall Through, abbreviated FWFT. In Standard mode the consumer requests the first word through a read operation. FWFT makes the first word available through a different sequence, without requiring the same initial read-enable action. Choosing a mode is part of the board's behavior, so a repair review should recover the original straps and reset sequence before changing a component or controller. Source: DSC-4294/8, p. 6, Standard/FWFT functional description.

The functional description says that reset-time FL, RXI, and WXI inputs select the timing configuration. Tables 3–5 on page 8 also distinguish programmable almost-full/almost-empty timing and buffered status options. Copy the applicable row into the board review record together with actual signal levels and reset timing assumptions. An undocumented strap should remain unresolved. Verify what drives those nets when reset is applied and released. Flag names and polarities depend on the selected contract: Standard-mode empty/full and FWFT output-ready/input-ready indications are not interchangeable software labels. Source: DSC-4294/8, pp. 7–8, Tables 1–5.

The datasheet describes additional flag buffering as a tradeoff involving clock-cycle delay. A controller that waits for a particular edge or polarity can consume stale data or stop at the wrong time if its interpretation changes. Keep the chosen flag configuration beside the stop-margin calculation, because a flag seen later leaves less time to stop. The source describes 513 words for 72V215 in FWFT when counting memory plus output register, compared with 512 in the Standard-mode fullness description. That additional output-register position does not justify rewriting all capacity assumptions to 513. The controller and flags must implement the corresponding FWFT semantics. Source: DSC-4294/8, pp. 6–9, mode capacity and flag buffering.

For a board validation plan, define expected results before recording observations: reset to empty; one write followed by a read request; first-word handling in the configured mode; repeated writes approaching almost-full; producer stop with all in-flight words accounted for; and reads through almost-empty to empty. Exercise the clock relationships permitted by the design, including consumer pauses. Record which data sequence and flag timing would constitute a failure. These are proposed checks, not a claim that simulation, synthesis, or hardware testing has been performed for the reader's assembly. Preserve the 512-word Standard-mode assumption in this dossier's worksheet unless the full behavioral contract is deliberately revised.

Close the 3.3 V interface before releasing a board

Check the voltage relationship in both directionsRecommended supply3.0to3.6volts, commercial operating temperature TA0to70C. Controller input to FIFO and FIFO output to controller require separate threshold and load checks. Conceptual interface, no pin assignments.RECOMMENDED SUPPLY3.0–3.6 V · commercial 0–70 °C72V215L10TFGCONTROLLER → FIFOInput HIGH ≥ 2.0 VFIFO → CONTROLLEROutput HIGH ≥ 2.4 Vat −2 mA; verify receiver + load
Original interface concept, not a pinout. Verify thresholds and timing with their stated loads and conditions.

The relevant recommended supply range is 3.0 to 3.6 V, with a 3.3 V typical value. For this commercial code the operating temperature TA range is 0 to +70 °C. Use those operating limits in the rail and environment review. Absolute maximum ratings serve a different purpose and do not expand the usable range. A substitution that changes the temperature suffix or supply family needs engineering assessment even when the organization remains 512 by 18. Source: DSC-4294/8, p. 4, recommended DC conditions; p. 25 commercial grade.

The L10 commercial AC column specifies a maximum clock-cycle frequency of 100 MHz and a minimum clock period of 10 ns. In the same column, the data-access interval is 2 ns minimum to 6.5 ns maximum, data setup is at least 3 ns, and data hold is at least 0.5 ns. These numbers have the stated supply and temperature conditions and the datasheet's AC test conditions, including its output load. They are inputs to a board timing analysis, not proof that an existing interconnect, receiving input, or controller operates at 100 MHz. Source: DSC-4294/8, p. 5, L10 commercial AC column and Figure 1 test load.

On the input side, the recommended high-level threshold starts at 2.0 V and the low-level limit is 0.8 V. On the output side, the DC table gives at least 2.4 V for a high at −2 mA and at most 0.4 V for a low at 8 mA. Compare guaranteed transmitter levels to receiver thresholds under actual loading. The family's 5 V input tolerance does not promise a 5 V output swing, and it does not make a receiving FPGA bank tolerant of whatever appears on the outputs. Review both directions independently. Source: DSC-4294/8, p. 4, recommended inputs and DC output levels.

Start a timing worksheet with the write launch edge, board propagation delay, setup/hold requirements, clock skew, and uncertainty. Make a corresponding read path using minimum and maximum output timing, receiver constraints, and routing. Check enable and reset timing as well as data. The user I/O budget helps count the two 18-bit buses and separate clocks before allocating controller pins; it cannot confirm bank voltages, pin assignments, skew, or timing closure. Those require the controller and FIFO documents and the released board.

Power estimation needs conditions beside the number. The 30 mA maximum active-current entry is tested with outputs disabled, clocks toggling at 20 MHz, and data inputs switching at 10 MHz. It is not a guaranteed 100 MHz, heavily loaded rail budget. Retain the engineer's operating-frequency, output-load, and activity assumptions in the regulator and decoupling review. A board's working history does not establish margin for a changed controller, longer trace, different load, or altered production environment. Source: DSC-4294/8, p. 4, active-current notes 4–6.

Source-bound facts; conditions travel with values
ParameterValue/categoryConditionsLocator
Organization512 ×18 bitsArray;9,216 bits calculatedDatasheet p.1
Supply3.0 min /3.3 typ /3.6 max VRecommended conditionsp.4
Operating temperature TA0 to+70°CCommercial codepp.4,25
Clock100 MHz maximum;10 ns minimum cycleL 10 commercial; VCC 3.3±0.3 V; TA 0–70°C; ACtestloadp.5
Access / data setup / hold2–6.5 ns /≥3 ns /≥0.5 nsL 10 commercial AC columnp.5
Input thresholdsVIH≥2.0 V; VIL≤0.8 VRecommended input limits; source VIL lower bound−0.5 Vp.4
Output thresholdsVOH≥2.4 V; VOL≤0.4 VAt−2 mA /8 mA respectivelyp.4
Active current30 mA maximumOutputs disabled;20 MHz clocks;10 MHz inputs; not a 100 MHz loaded limitp.4 notes 4–6
Package/carrier64 leads; PPG 64; tray10×10×1.4 mm;0.5 mm pitch; MSL 3; e 3 SnExact-part Package Information

Use the package record to prepare manufacturing questions

Separate the package record from the land patternA conceptual leaded package has a record for64leads,0.5mm pitch,tray andMSL3. Separate drawing, footprint and pin-map reviews follow. Not to scale, not a footprint, not a pinout.PACKAGE IDENTITYConceptillustration64 leads · 0.5 mm pitchTray · MSL 3 · green finishCheck drawing + footprintCheck the pin map separatelyNot to scale · no pad or pin data
Original package-record concept, not to scale, not a footprint, not a pinout. No manufacturing coordinates are supplied.

Renesas's exact-part page lists 64 leads, a TQFP package classification, package code PPG64, a 10.0 × 10.0 × 1.4 mm package-dimension entry, and 0.5 mm pitch. It also lists lead-free status, e3 Sn finish, tray carrier, and moisture sensitivity level 3. The older datasheet ordering table calls TF a slim thin plastic quad flatpack, with PP64-1 as its package reference. Preserve both source labels when comparing a historical drawing with a present ordering record. The page's dimensions are identification data, not a solder-land specification. Source: exact-part Package Information and Product Attributes, fetched November 10, 2026. Source: DSC-4294/8, p. 25, package/ordering references.

Ask the board owner for the released footprint and the original manufacturer mechanical drawing revision used to create it. Compare body dimensions, lead geometry, lead pitch, seating-plane information, orientation, and tolerances against that drawing. Verify the pin map from the official device pin configuration separately. A package outline, pin-assignment figure, and recommended PCB land pattern answer different questions. This dossier supplies a conceptual package-record illustration only. It provides no new pad coordinates, lead tolerances, stencil apertures, or assembly-process limits. Source: DSC-4294/8, p. 2, official pin configuration.

For a lot offered after the historical shipment milestone, include the condition of its moisture-barrier packaging, humidity indicator and desiccant records where applicable, storage history, and any prior opening or processing. MSL 3 is a classification, not evidence that this tray was stored correctly. Have the assembler determine handling and necessary conditioning from actual lot information and applicable process instructions. Do not assign an invented bake schedule or declare a lot solderable solely from an online package field.

The hardware and PCBA review service is relevant when the task includes assembly of a legacy controller board. Identify this component explicitly as a fine-pitch leaded package in the brief. Include the BOM, schematic, layout, stack-up, assembly revision, quantity, inspection plan, and functional acceptance criteria. If the board changes, the PCB fabrication review needs corresponding manufacturing files and constraints. No board or assembly approval is implied.

A receiving plan separates identity evidence from workmanship and function. The buyer checks agreement between documents, markings, and the ordered code. The assembler checks handling and assembly readiness. The board engineer defines data-integrity and flag-behavior acceptance work. A clean label does not replace those later checks, and a successful bench exercise on one sample would not independently authenticate every part in a purchase lot. Keep each result and its scope attached to the actual lot and board revision.

Turn 25 boards into a reviewable sourcing request

Base demand and commercial conditions are separate25boards multiplied by one FIFO per board gives25devices. Spares, losses and carrier rounding are separate decisions. Lot and delivery evidence remain open. Procurement concept.REVIEWABLE BASE DEMAND25 boards×1 per board25 devicesAdd only approved extras:spares · losses · carrier roundingLot + delivery evidence stays open
Original quantity workflow. Base demand 25 excludes spares, losses and pack rounding; stock and delivery remain unconfirmed.

For the purchasing example, assume one FIFO per board and 25 boards. Base demand is 25 devices. Yield loss, engineering samples, service spares, minimum order quantity, and carrier rounding are separate decisions; none is included automatically. The example quantity 25 in the quotation link is an editable request, not a manufacturer pack size or an availability claim. Keep the released board revision and exact requirement beside the quantity so a supplier cannot resolve a shortfall by silently changing the part.

Use the existing BOM completeness check for interactive quantity and reference review. Set Number of boards to 25. Paste the three-column tab-separated sample below, retaining the complete MPN, per-board quantity 1, and explicit reference U12. Run the check and inspect the reference count and calculated 25-device demand. Save the report with the BOM revision. If the real schematic uses a different reference, replace U12 first. This tool checks the supplied row and arithmetic; it does not verify that the reference exists in the schematic or that the component is suitable.

The static worksheet preserves the calculation when a tool is unavailable. It also records the capacity assumptions: Standard mode, 25 million accepted writes per second, occupancy 128, and reserve 64. Resulting headroom is 320 words or 12.8 microseconds. Keep the outputs separate: 25 is a procurement demand, while 12.8 microseconds is an illustrative engineering budget. Increasing purchased quantity does not improve one board's FIFO depth or stop latency. Revise the worksheet when the actual inputs differ.

The public 6116LA20SOG8 sourcing dossier is a useful contrast when sorting an old memory BOM: it concerns a 5 V asynchronous SRAM rather than this clocked streaming FIFO. It is not an alternate recommendation. Their different organizations and interfaces answer different maintenance questions. A new FPGA with sufficient raw memory bits is likewise a redesign direction only. It needs a controller, legal memory configuration, clock-domain handling, constraints, and validation of the required observable behavior. PLC250016 names no replacement for this exact row. Source: PLC250016, p. 3, replacement field None.

Continue evaluating a lot when its identity, commercial grade, package, carrier, and documents match the released requirement and the board owner can recover the FIFO mode and timing contract. Stop release if a supplier changes the code without review, reset configuration is unknown, the producer cannot stop within established margin, or lot condition remains unacceptable to the receiving and assembly plan. Present stock, price, shipment date, lot authenticity, and board compatibility remain unverified.

For an executable request, supply destination, required delivery date, acceptable date-code policy, traceability documents, and inspection or test requirements. State whether it is exact-code-only and whether a supplier may propose a separately identified redesign candidate. The next action is to get price and lead time for 72V215L10TFG, quantity 25, then review the populated request and edit it before submission. This dossier used AI assistance and the cited original sources; no independent human engineering sign-off or completed hardware test is claimed.

Static worksheet: replace assumptions before use

Input/outputWorked valueReview rule
Boards ×devices/board25 ×1 =25 devicesNo loss, spares or pack rounding
Mode /depthStandard /512 wordsRecover reset configuration
Rate /occupancy25 Mwords/s /128 wordsApplication assumptions
Stop reserve50+10+4 =64 wordsStop response+pipeline+visibility
Headroom512−128−64 =320 wordsCommon word definition
Stall budget320/25,000,000 =12.8µsNo reads in assumed stall
Action threshold512−64 =448 wordsDefault 63 offset gives 449; review it

Paste into the BOM tool

MPN	Qty	Ref
72V215L10TFG	1	U12

Set board count to 25.Expected base demand:25 devices; one explicit reference matches Qty 1.Inspect actual output before saving or sharing.No enquiry is submitted by this example.

Evidence review: November 10,2026.AI-assisted source analysis and original illustrations.No live inventory feed, supplier quote, independent human engineering certification, simulation result or hardware test is represented.

Back to Hard-to-find →

Source addresses and citation trail

Full source addresses are retained below. Read each citation with its document revision, page, table and applicability conditions above.

  1. https://www.renesas.com/en/products/72v215/part-details/72v215l10tfg
  2. https://www.renesas.com/en/document/dst/72v205-72v245-datasheet
  3. https://www.renesas.com/en/document/eln/plc-250016-end-life-eol-process-select-part-numbers?r=13431