BASE DEVICE
10M02
MAX 10 base device.
- Logic elements
- 2 K LE
- M9K memory
- 108 Kb
- 18x18 multipliers
- 16 multipliers
1 ordering code10M02SCE144I7G →
Specifications & documents →Altera / Chips & IP
MAX 10
Nonvolatile FPGA family with configuration flash, embedded memory and DSP; selected devices add analog and memory-interface functions.
Product lines are representative. Stock, lifecycle, package and grade must be checked against the exact MPN.
Product scopeChips & IP
Device references in this category2
Documented ordering codes16
Information checked2026-09-28
FROM FAMILY TO DEVICE
Chip models in MAX 10
Documented device references
Base-device names are distinct from full ordering numbers. Each detail page identifies the product type, parameter scope and official source.
BASE DEVICE
10M50
MAX 10 base device.
- Logic elements
- 50 K LE
- M9K memory
- 1638 Kb
- 18x18 multipliers
- 144 multipliers
2 device references
No model matches this search. Clear the filter or send the exact part number for review.
Browse the full Altera product map →
SELECTION CONTEXT
Working with MAX 10
Define the required function
Nonvolatile FPGA family with configuration flash, embedded memory and DSP; selected devices add analog and memory-interface functions.
Use the requirements below to decide which specification limits your design. A family name alone is not a purchasing specification.
Check the integration boundary
Choose the complete device and ordering code before checking package pinout, power, electrical limits and operating grade. Keep family maxima separate from a selected device or package.
Open the manufacturer reference ↗ENGINEERING DECISIONS
What to confirm before selection
Use these checks to define the requirement. Family names alone do not establish performance, package compatibility or current availability.
- Check ADC availability and the exact package.
- Review configuration mode, power sequencing and external-memory limits.
Move from family to full ordering number
Identify the complete manufacturer part number, package, operating grade and electrical requirements. Reviewed FPGA specifications can then be compared at device level.
Browse reviewed FPGA device data →Preparing a complete board?
Bring the BOM, schematic constraints, stack-up and assembly requirements into the project brief.
PCBA project preparation →EVIDENCE & DEVELOPMENT
Documents for this product line
Start with the device table, then check electrical limits, ordering information and the applicable tool release.
MAX 10 — manufacturer referenceManufacturer product documentationPrimary source ↗MAX 10 FPGA Device OverviewTable 4, Maximum Resource CountsWeb ↗
More Altera development resources
Altera FPGA documentation ↗
Device handbooks, data sheets, errata and development-kit guides.
Quartus Prime ↗
Edition selection, downloads and release-specific design resources.
Development kits and boards ↗
Official entry point for Altera kit families and partner offerings.
Altera community ↗
Technical discussion and product-support knowledge.
These broader manufacturer resources do not establish support or compatibility for every device on this page.
PRACTICAL QUESTIONS
MAX 10 selection questions
How do I select a model within MAX 10?
Start with the documented product scope: Nonvolatile FPGA family with configuration flash, embedded memory and DSP; selected devices add analog and memory-interface functions. Then compare the device-specific facts below with your required resources and interfaces. Open each model for its evidence and ordering constraints.
Is a base-device name enough to place an order?
A base-device identifier identifies the silicon or model, but may omit package, speed, temperature, qualification and packing options. Use the manufacturer ordering table to establish the complete code. Reference examples do not establish stock or an approved replacement.
Can the listed devices use the same PCB or development tools?
A shared family or manufacturer does not establish pin compatibility. Compare pinout, supply and I/O-bank voltages, configuration, timing, tool support and thermal limits before changing a board.
What should I include for sourcing or PCBA review?
Provide the exact part or board revision, quantity, delivery requirement, operating environment and traceability needs. For assembly, identify BOM readiness, PCB stack-up, programming access and the inspection or functional-test scope.
PREPARE A USEFUL INQUIRY
Build your selection brief.
Select the points you want our team to review. Your selections stay in this browser until you choose to submit the quotation form.
Open quotation form →Sources & portfolio context
Source review: 2026-09-28. This family guide does not assert stock or compatibility between devices.
← Complete Altera product map